Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › Strip-Till Unit Calibration Worksheet

Strip-Till Unit Calibration Worksheet

Strip-till only pays when the strip lands where the planter will run. This worksheet walks through depth, tool spacing, fertilizer rate and records so you can set up a unit and trust it.

Worksheets, Checklists & Calibration Guides3 min read702 words

In short

  • Match shank spacing and strip centerline to the planter, and check every row, not just the middle ones.
  • Dig and measure strip depth and shape, then verify fertilizer rate with a catch test and a speed check.
  • Keep a page per field with settings and conditions, and get custom operators to commit to numbers in writing.

What you are calibrating

A strip-till unit does three jobs at once: it loosens a band of soil, places fertilizer in or beside that band, and leaves a seedbed that the planter can find. Calibration means checking that each of those jobs is happening at the setting you intended, on every row, at your working speed. The only reliable source for settings is your unit's manual and your fertilizer label, plus advice from your agronomist or Extension office on depth and nutrient rates for your soil and crop. What follows is the method for checking and recording those settings. Use a notebook and a tape measure. Write the date, field, soil moisture, tractor gear and engine speed at the top of each page, since a setting is only meaningful with its conditions.

Row spacing and strip position

Measure the distance between shanks with a tape and compare it to your planter row spacing. They should match or be a clean multiple. Then check the centerline. Pull the toolbar into the field, drop the unit, drive twenty feet, and stop. Dig across three strips and measure from a fixed point such as a stake to the strip center. Do the same on the outer rows. If rows near the wings sit off center, check wing level and hitch height before blaming the guidance. Mark the result for each row. A planter running half a strip width off center plants into firm ground, which defeats the purpose and wastes the fertilizer too.

Depth and strip shape

Dig a clean cross-section of the strip with a flat shovel and measure with a ruler. Record the tilled depth, the width of loosened soil, and the height of the ridge above the surrounding ground. Compare those numbers with what your agronomist recommends for your soil. Then check each row. If the outer units run shallower, the usual causes are toolbar level, worn points or a depth gauge wheel set unevenly. Adjust one thing at a time and re-measure. Check coulters and residue cleaners as well, since a clogged unit pushes residue into the strip. Record the settings that worked and the soil condition, because the same setting in wet clay and dry loam gives very different results.

Fertilizer rate by arithmetic

For liquid or dry placement, confirm the rate with a catch test, following the controller and pump manual. Say you want 40 pounds of nitrogen per acre. If your fertilizer is 28 percent nitrogen and weighs about 10.7 pounds per gallon, a gallon carries roughly 3 pounds of nitrogen (10.7 times 0.28 is about 3.0). Forty divided by 3.0 is about 13.3 gallons per acre. Check the product label or supplier sheet for the real density rather than relying on this figure. Now check the ground speed. Mark off a distance, time it, and compute miles per hour. A radar or GPS reading can drift, so verify once per season. Then catch output from each row for one minute and compare rows. Any row more than a few percent off the average needs a clean orifice, filter or line.

Records, hired passes and mistakes

Keep one page per field with settings, measurements and who ran the pass. If a custom operator does the strip-till, ask what depth, spacing and rate they will run, and ask for those numbers in writing along with the product and rate applied. Ask how they handle skips and overlap. A few common mistakes: running too fast so the shanks float, setting depth on one row and assuming it carries to the rest, forgetting to re-check after hitting rock, and skipping the catch test because the monitor looked fine. Application records can matter for nutrient plans and for regulation, and rules vary by state, so confirm with your state department of agriculture or Extension office.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading