Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › Spring Planting Equipment Checklist

Spring Planting Equipment Checklist

A planter that sat all winter needs a real look before the first field. Here is what to check, what to write down, and when to call a shop.

Worksheets, Checklists & Calibration Guides3 min read767 words

In short

  • Use the manual and last season's notes as your starting list, then work from the hitch back to the row units.
  • Test meters, monitor and hydraulics before planting season, and get shop findings in writing with an itemized invoice.
  • Finish with a short test pass and dig seeds to verify depth and spacing.

Start with the manual and last year's notes

Pull the operator manual for the planter, drill and tractor before you touch a wrench. The manufacturer lists service intervals, torque values, grease points and chain or bearing specs that no checklist can replace. Then find the notes from last season. If you wrote down that row unit three was skipping or the monitor threw a seed-tube error in the last field, that is your first job. If you hire a dealer or a custom shop for the work, hand them that list so they are not guessing. A shop can only fix what it knows about, and a vague request like "go through the planter" tends to get a vague bill and a missed problem.

Frame, hitch and tires

Walk the machine slowly with a flashlight. Look for cracks at welds, bent toolbar sections, loose U-bolts and worn hitch pins. Check tire pressure against the sidewall and the manual, since planter transport tires are often run too soft or too hard after months of sitting. Look for dry rot and sidewall bubbles. Grease every fitting on the frame, wing hinges and wheel hubs, and pull a wheel bearing if a hub feels rough or runs warm. Test hydraulics by folding and unfolding the wings, raising and lowering, and watching for leaks or slow cylinders. A weeping hose or cylinder seal is cheaper to fix in the shop yard than in a muddy field with the forecast turning.

Row units, openers and closing wheels

This is where stands are made or lost. Check each opener disc for wear and for the gap between the discs; the manual gives the wear limit and the method, often a simple feeler or wear gauge. Worn discs leave a poor furrow and let seed ride up. Inspect gauge wheels, depth-adjustment arms and bushings for slop. Spin closing wheels and press wheels by hand and replace any that bind or wobble. Look at the parallel arm bushings, since sloppy bushings let a unit wander and plant at uneven depth. Keep a tally on paper: unit number, part, condition. That tally becomes your parts order and your proof of what was replaced.

Seed delivery, meters and drives

Open each seed meter and clean out old treatment dust and trash. Check brushes, belts, seed discs and seals against the manual, and replace worn pieces as a set instead of one at a time. Inspect seed tubes for cracks or build-up, and confirm sensors are clean. On chain or electric drives, check chain tension and slack, sprockets for hooked teeth, and wiring for chafing. Run the planter on a test stand or have a dealer do it, then compare the singulation and spacing they report with what the manual calls acceptable. Ask whether they will give you the results in writing. If a meter is borderline, replace it. Skips in a stand cost more than a meter.

Monitor, hoses and the tractor side

Power up the monitor and confirm every row reads. Check the configuration for seed count, row spacing and implement width against the machine in front of you, because a wrong width setting quietly ruins your acre counts. Inspect air hoses for cracks, the fan for noise or vibration, and the vacuum gauge for a steady reading. For liquid or dry fertilizer attachments, inspect lines, filters and check valves, and rinse or flush according to the product label. On the tractor, look at tires, hitch category, hydraulic couplers, lights and the SMV emblem. A tractor that cannot hold the planter at working speed in the field is a bad time to learn that.

Paperwork, labor and a dry run

Write down the date and findings, the parts replaced, who did the work and what they charged. If a shop did it, ask for an itemized invoice and a note of anything they saw but did not fix. Confirm who will be running the planter and whether they have run this model before. Rules on hired labor and licensing vary by state, so confirm with your state department of agriculture or Extension office. Then do a dry run: hook up, fold, unfold, plant a short pass, and dig a few seeds to check depth and spacing. Look up your state in the directory to find service providers near you.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading