In short
- Catch and compare nozzle output in ounces per minute, and replace tips more than about ten percent over rated flow.
- Use gallons per acre equals gallons per minute times 5,940, divided by speed times spacing.
- Replace tips as a set and keep a written record of every check.
Why Nozzles Wear Out
Spray tips are small precision parts. Abrasive products such as wettable powders and some fertilizers wear the orifice, so it gets bigger and puts out more liquid. Brushes, wires and pocketknives used to clear plugs scratch the edges and distort the pattern. Different tip materials wear at different rates; stainless steel and ceramic last longer than brass or plastic, but the cost differs, and your dealer can explain the options. A worn tip does not look worn. You will not see it from the cab, which is why you need a number. A nozzle that is ten percent over its rated flow is a commonly used point to replace tips, but follow your nozzle manufacturer's guidance.
Check Flow at Each Nozzle
Fill the tank with clean water. Run the sprayer at the working pressure and catch the output from each nozzle for a set time, such as one minute, in a container marked in ounces. One gallon per minute is 128 ounces per minute. A tip rated for 0.4 gallon per minute at that pressure should give about 51 ounces in a minute (0.4 times 128 is 51.2). Write down each reading by position on the boom. Compare each nozzle with the new rated flow in the manufacturer's chart and with the average. Replace any nozzle that is more than ten percent off, or follow a stricter limit if the label or your agronomist asks for one.
Worked Calibration Example
The usual formula is gallons per acre equals gallons per minute per nozzle times 5,940, divided by speed in miles per hour times nozzle spacing in inches. With 0.4 gallon per minute, 5 miles per hour and 20 inch spacing, that is 0.4 times 5,940, which is 2,376, divided by 5 times 20, which is 100. The answer is 23.76 gallons per acre. If the real output is 0.44 per nozzle, the sprayer applies 26.1 gallons per acre, about ten percent more than planned. Confirm speed by timing a measured distance in the field, since the tractor monitor can be off, and check the pressure gauge against a known gauge.
What to Record
Use one page per sprayer. Write the date, nozzle make, model, size, material and spacing, the pressure, travel speed and the flow reading for each nozzle. Note tips replaced, hours or acres since the last replacement, and the products sprayed, especially abrasive ones. Note the gauge check and the speed check. Keep the earlier records so you can see how fast wear shows up on your equipment. After two seasons you will have a decent idea of when to schedule replacement before it becomes a problem. Keep the sheet with your application records, since many pesticide records requirements apply to restricted-use products and rules vary by state.
Common Mistakes
Do not mix tip types across the boom unless the system was designed for it. Do not replace one worn tip and leave the others, since the new one will put out less than the rest and make a streak. Do not clean tips with metal objects; use a soft brush or a toothpick. Do not rely on the sprayer controller alone, since it computes from settings and cannot see a worn orifice. Do not forget screens and check valves, because a plugged screen drops flow and a stuck check valve causes dripping. Do not calibrate with product in the tank unless the label and your plan call for it.
When to Get Help
If flow readings vary a lot across the boom even with new tips, look at the plumbing, pump, strainers, section valves and pressure regulator. Ask the dealer to check the pump and controller. If you use a custom applicator, ask how often they replace nozzles and whether they can show you their calibration records. Ask the state department of agriculture or Extension whether workshops or certified calibration help are offered. Pesticide applicator licensing and recordkeeping rules differ by state; confirm what applies to you. Look up your state in the directory for sprayer repair and custom application providers.
Find providers near you
Pick your state to see vets, custom operators, dealers, elevators and other farm services.
