In short
- Test the spreader with the real product, using trays and a scale, before the first field.
- Rate equals pounds caught times 43,560, divided by swath width times distance, then convert nutrient to product weight.
- Record settings and retest after any change in product, wear or repairs.
Why a dial setting is only a starting point
The chart on the spreader or in the manual was built with a certain product, at a certain density, on a certain day. Your fertilizer may be a different granule size, a different weight per cubic foot, or damp from the bin. Wear in the gate, vanes and bearings changes things too. So treat the chart as a first guess and test the machine with the product actually going on the field. Read the manufacturer manual and the fertilizer label first, because they set the safe tractor speed, spinner speed and any limits on the product. A bad setting is not just wasted money. Too little leaves yield on the table, and too much can burn a crop or end up in a ditch.
Check the swath with collection trays
Put out a row of shallow pans or cardboard boxes of equal size across the driving line, spaced evenly, with the spreader driving down the middle. Many universities publish tray test methods, so look for one from your state Extension service. Drive through at your normal speed and PTO speed, then pour each tray into a measuring cup or weigh it. Plot the amounts. A good pattern is even across the middle and tapers smoothly at the edges. If one side is heavy, check that the drop point on the spinner is centered and that the vanes are not bent or worn. Write down which setting produced which pattern.
Work out the rate from a catch test
Rate is the weight spread divided by the area covered. The formula is pounds applied times 43,560, divided by swath width in feet times distance driven in feet. Here is a worked example. Say you run 200 feet with a 40 foot effective swath, which covers 8,000 square feet. You catch 18 pounds of product, which you can do with a tarp or by weighing what left the hopper. Eighteen times 43,560 is 784,080, divided by 8,000 is about 98 pounds per acre. If you wanted 120, open the gate a bit and test again.
Convert nutrient to product
Fertilizer labels show percent nutrient, so you set the machine by product weight, not nutrient weight. If you want 100 pounds of nitrogen per acre from urea, and urea is 46 percent nitrogen, divide 100 by 0.46. That is about 217 pounds of product per acre. For blends, each nutrient comes at its own percentage, so figure the product rate from the nutrient you are driving, usually nitrogen, and let the others follow. Your soil test report and the recommendation from an agronomist or Extension office tell you the nutrient target. The spreader only delivers what you tell it.
Effective swath and overlap
The effective swath is not the distance the fertilizer is thrown. It is the driving spacing that gives an even blend once passes overlap. Most spreaders throw farther than they spread evenly. Using the full throw width leaves streaks. Test by running tray tests with overlapped passes, which means the tray catches product from two passes, and look for a flat total. Then set your guess row, GPS lines or tramlines to that spacing. Wind matters, so spread in low wind and recheck when product or conditions change.
What to record and when to retest
Keep a card in the cab with product, bag or bulk lot, setting, tractor gear, PTO speed, swath spacing and measured rate. Retest when you change products, after repairs to vanes or gates, and at the start of each season. Ask any custom applicator how often they calibrate, and ask to see the last record. If you hire the work, put the target rate, product and fields in writing, and ask about their calibration before the job. Your state department of agriculture can tell you what rules apply to fertilizer application near water, and whether a custom spreader needs a license.
Common mistakes
The usual errors are easy to avoid. People calibrate with one product and then switch blends without a retest. They test at a slow tractor speed and then drive faster in the field, which changes the pattern. They forget to check that the hopper is level, or they let product bridge over the gate so the rate drops mid-field. Wash the machine after use, because wet fertilizer eats gates and vanes. Follow the product label for any buffer around ditches, wells and streams, and ask your state department of agriculture if you are unsure what rules apply.
Find providers near you
Pick your state to see vets, custom operators, dealers, elevators and other farm services.
