Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › Orchard Sprayer Calibration Worksheet

Orchard Sprayer Calibration Worksheet

Calibrating an airblast sprayer means matching nozzle output, ground speed and row spacing to the gallons per acre you intend to apply. The arithmetic is simple when you take it in order.

Worksheets, Checklists & Calibration Guides3 min read675 words

In short

  • Measure speed over a marked distance and catch each nozzle's output for one minute.
  • Use 495 times gallons per minute divided by mph times row spacing for gallons per acre.
  • Follow the label for rates and keep dated calibration records.

Read the label first

The product label sets the legal limits, and often the dilute or concentrate approach, so calibration begins there. Check the rate per acre, the maximum gallons of water if one is given, the buffer and drift language, and the days before harvest. Your university Extension fruit specialist can tell you how growers in your region adjust for tree size and canopy density. Calibration only tells you what the machine delivers. It does not decide what the right rate is. If the label and your equipment disagree, the label wins. Pesticide applicator licensing and recordkeeping rules vary by state, so confirm yours with your state department of agriculture.

Measure your ground speed

Speed is the number everyone guesses at. Mark off 200 feet in a row middle, with flags at each end. Drive it at the gear and engine speed you spray at, with the tank half full, and time the run in seconds. Then miles per hour equals the distance in feet divided by the seconds, multiplied by 0.682. Check it: at 2.5 miles per hour you cover about 3.67 feet per second, so 200 feet takes about 54.5 seconds. If your run takes 54 seconds, you are close to 2.5 mph. Do the run twice, once in each direction, and average the two. Write it down with the gear and RPM.

Measure nozzle output

With the sprayer parked and clean water in the tank, run it at the working pressure and catch the output of each nozzle in a container for one minute. A measuring jug in ounces or milliliters works. Record every nozzle. Compare them to the chart for that nozzle at that pressure. Replace any that are more than a few percent off the chart, and replace worn nozzles as a set. Then add up all the open nozzles and convert to gallons per minute. If your total comes to 12 gallons per minute, you now have the first number you need for the formula.

The gallons per acre formula

For an airblast sprayer that covers every row, gallons per acre equals 495 times the total gallons per minute, divided by the product of miles per hour and row spacing in feet. As a worked example, 495 times 12 gallons per minute is 5,940. With a speed of 2.5 mph and row spacing of 18 feet, the divisor is 45. That gives 132 gallons per acre. If you spray only every other row, the formula changes, so work it through carefully for your pattern. To raise the rate, change nozzles or pressure, or drive slower. To lower it, do the opposite.

Tank mix and records

Once you know gallons per acre, work out how many acres a tank covers. A 500 gallon tank at 132 gallons per acre covers about 3.8 acres. Then calculate product per tank from the label rate, and double-check with someone else. Record the date, nozzle set, pressure, speed, output, gallons per acre and who calibrated. Do it at the start of every season and after any nozzle or pump change.

Mistakes to avoid

Do not calibrate with a worn pump, skip the speed check or trust the pressure gauge without testing it. Check the gauge against a known good one.

Canopy and coverage

The gallons per acre number only matters if the spray reaches the canopy. Tie bits of water-sensitive paper or flagging tape at several heights in a tree and spray with plain water to see where it lands. Close down the top nozzles on small trees so you do not spray the sky, and adjust the fan speed and nozzle angles per the manufacturer. Wind and temperature change drift and coverage, so pay attention to the label restrictions and your state rules on application conditions.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading