Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › GPS & Auto-Steer Calibration Record

GPS & Auto-Steer Calibration Record

Auto-steer only drives straight if its setup is right. This guide shows what to measure, what to write down and how to catch drift before it costs you.

Worksheets, Checklists & Calibration Guides3 min read702 words

In short

  • Write down antenna position, implement offset and tire data, with dates.
  • Test pass to pass gaps in both directions after every calibration.
  • Redo calibration after changing tires, weight or antenna location.

What the record is for

When auto-steer pulls to one side, or passes do not match, nobody remembers what was changed last spring. A written record fixes that. It lets you compare today's behavior to a known good setup, it helps a dealer technician work faster, and it is useful if you share the tractor or hire someone to run it. Keep a simple notebook in the cab or a file on your phone, one page per tractor or machine, and update it whenever something changes. Use the manufacturer manual for the actual calibration steps, because they differ between brands.

Measurements to write down

Start with the physical facts. Record the make and model of the receiver, the correction source such as a base station or subscription service and its accuracy level, and the antenna height above the ground. Note the antenna position left or right of the tractor center and ahead of or behind the rear axle, because the system needs these to find the machine. Add tire size and pressure, since changing tires changes rolling radius. Record the implement width and its offset to the left or right of the tractor center. Mark each number with the date changed, in the log.

Roll and wheel angle calibration

Most systems ask you to drive a straight line one way, turn around and drive the same line back, so the receiver can learn the roll error from the slope of the ground. Do this on a flat, open spot, at the speed the manual says. Then calibrate the steering sensor so the system knows what straight ahead looks like. Write down the date and the values the screen gives. If you later change tires, add weight or move the antenna, redo these steps rather than hoping the old numbers still work.

Check pass to pass accuracy

After calibration, run a field test. Drive a line, then turn around and drive an adjacent pass with the implement down, and measure the gap or overlap at several points along the pass. Do it in both directions. Next, the next day, go back to the first line and see how far it drifted. Note the correction type, because pass to pass accuracy is far better than year to year accuracy unless you use a fixed base. Write the measured gaps in the record.

Count the cost of overlap

Overlap is easy to see in money. Say you run a thirty foot implement and you overlap one foot on every pass. That is one thirtieth, or about 3.3 percent, of the work done twice. On a thousand acre farm, that means about thirty three acres of extra seed, fertilizer, chemicals and fuel. Tighter overlap pays for the setup time, but get the actual costs from your own inputs. Keep the numbers from your own passes instead of trusting a brochure.

Troubleshooting and hiring help

When something drifts, check the common causes in order. Is the correction signal at its normal accuracy level? Has the antenna been bumped or the mount loosened? Did tire pressure or implement offset change? If these check out, call the dealer, bring your record, and ask what they changed. If you hire a precision ag service to set up or map fields, ask which datum and line formats they use, who owns the files, and get the settings in writing.

Sample record layout

A record page does not need to be fancy. Head it with the machine name and the date. Then list the receiver and correction source, antenna height, antenna offset, tire size, implement width and offset, and the screen values from the last roll and steering calibration. Below that, keep a short log with one line for each field test, giving date, field, speed, measured pass-to-pass gap, and any note such as wet soil or slope. A photo of the setup screen taken after each calibration is a cheap backup. Store a copy somewhere other than the cab, since a failed display or a sold tractor can take the only copy along.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading