Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › Broadcast Seeder Calibration Worksheet

Broadcast Seeder Calibration Worksheet

A broadcast seeder throws seed in a pattern, so calibration means finding both the flow rate and how wide the seed really lands. Here is the worksheet method.

Worksheets, Checklists & Calibration Guides3 min read670 words

In short

  • Measure effective swath with pans, not by how far the seed flies.
  • Pounds per minute equals rate per acre times acres per minute; catch and adjust.
  • Record gate setting, seed and result to start closer to right next time.

Two things to measure

A broadcast seeder, whether spinner, cyclone or drop spreader, has to be calibrated for two things. One is how many pounds leave the hopper each minute. The other is the effective swath, meaning the width over which the seed lands evenly enough to overlap. Many people set the first and skip the second, and end up with stripes in the pasture. The seeder manual will give a starting setting for each seed type. Treat it as a starting point only, because seed size, coatings and weather change the outcome.

Find the real swath width

Lay out a row of shallow pans, trays or cut-down boxes across the pass at regular intervals. Drive through at working speed with the seeder running. Then weigh or compare the seed in each pan. The pattern will be heavier near the center and lighter at the edges for many spinners. Pick the width at which the rate falls to a level you can overlap. If it is 20 feet, then your passes should be about that far apart or a bit less, not the full distance the seed can fly. Ask Extension about overlap guidance for your equipment.

Calculate the target flow

Say you want 10 pounds of seed per acre, driving 4 miles per hour with a 20 foot swath. Acres per hour equals 20 times 4 times 5,280 divided by 43,560, which is about 9.7. Divided by 60, that is about 0.162 acres per minute. At 10 pounds per acre, the hopper must release about 1.62 pounds per minute. If you want it per 100 feet instead, remember that an acre is 43,560 square feet and plan the travel distance accordingly.

Catch test the hopper

Park the seeder, jack it or place a tarp under the outlet as the manual allows, and run it at working power takeoff or motor speed for one full minute. Catch the seed and weigh it. Suppose you catch 1.3 pounds when 1.62 is your target. Divide 1.62 by 1.3 to get about 1.25, so open the gate about 25 percent more. Test again. Small seed like clover can bridge in a hopper, so tap or stir and watch for flow changes. Do three runs and average them.

Adjust for the real world

Wind can throw light seed far off the pass, so avoid windy times. Wet seed and dusty seed flow differently from dry seed. If you blend seed, such as a mix of grass and clover, the heavier seed may settle and the mix will change as the hopper empties. Keep stirring or run the hopper lower. Fertilizer and seed mixes behave in their own ways, so follow the product label and manual. Check emergence two or three weeks later and look for bare strips.

Keep a worksheet

Record the date, seed, lot, gate setting, speed, swath, catch weight and the result in the field. When you buy the same seed next year, you will start closer to right. Your county Extension office or a seed dealer can help with pasture seeding rates, and your state agriculture department can explain seed labeling for the lot you bought.

Common mistakes to avoid

The mistakes are predictable. People calibrate on a bench but drive faster in the field. They pick a swath width based on how far seed flies instead of how evenly it lands. They forget that a lighter hopper feeds differently from a full one. They calibrate with one seed, then plant a different lot. Another common one is skipping the second test after an adjustment, so the first correction overshoots. Run the test again every time you change a setting. And when the field is done, compare seed used to acres covered. If the two disagree, the worksheet tells you where to look.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading