In short
- Walk the rig every trip: hitch pin, chains, tires, hoses, lights and tie-downs.
- Lock folded implements with mechanical pins and mark wide loads with clean emblems and reflective tape.
- Check width, weight and permit rules with your state transportation agency, and keep written notes.
Walk the Rig Before You Pull Out
Do the walk-around every time, even for a half-mile trip to the next field. Start at the hitch. Check that the pin is the right size, fully seated and clipped, and that the drawbar or receiver is not cracked or worn oval. Safety chains should cross under the tongue and be rated for the load, with enough slack to turn but not enough to drag. Check tires for cuts, bulges and low pressure, and look at lug nuts or wheel bolts on trailers. Check hydraulic hoses for chafing where they pass near the frame. Look under the rig for fresh drips. Ten minutes of looking is cheaper than a ditch, a tow bill and a phone call to the insurance agent.
Lights, Marking and Visibility
Most road crashes involving farm equipment happen because another driver came up on a slow machine faster than expected. Turn on every light and walk around to confirm it works: headlights, taillights, turn signals, hazards. A slow-moving vehicle emblem should be clean, unfaded and mounted where following traffic can see it. Replace emblems that have gone pale orange or are caked in dust. Add reflective tape on wide implements, extension wings and the corners of trailers. Wipe lenses before dawn or dusk runs. If an implement blocks your lights when raised or folded, you need auxiliary lights or a different transport position. Lighting and marking requirements differ by state, so check with your state department of transportation or the highway patrol.
Secure the Load and Fold the Implement
Folded implements should be locked with the manufacturer's transport pins or latches, not just held by hydraulic pressure. Hydraulic systems leak down, and a wing that drops on a bridge is a bad day. Raise and lock tillage tools, lower or lock loader buckets as the manual directs, and park the PTO driveline in its stored position. For hauled cargo such as bales, tanks or equipment on a trailer, use tie-downs and chains with working load ratings that match the weight, and check them again after the first mile because loads settle. Cap fuel and fluid tanks and close grain gates. A chain that looks fine can have a stretched link, so retire damaged ones.
Weight, Width and Permits
Know the actual weights of your tractor, the implement and the trailer, and compare them with the tractor's recommended drawbar load and the trailer's rating. A heavy implement behind a light tractor can push the tractor on downhill grades and make braking poor. Width, height, length and weight limits for farm equipment on public roads vary by state, and many states allow exceptions for implements of husbandry but still require flags, lights or escort vehicles above certain widths. Call your state department of transportation or county road office before moving oversize equipment, and ask whether time-of-day limits, bridge restrictions or permits apply. Write down who you spoke with and the date of the call.
Plan the Route and Drive for the Conditions
Pick the route before you start. Look for narrow bridges, low wires, railroad crossings, school bus times and blind hills. Ask the county road office about weight-limited bridges, especially during spring thaw when some roads are posted. Keep speed within what the equipment and the manual allow, since some implements are not rated for fast road travel. Leave extra stopping distance, because loaded wagons and heavy implements can push the tractor. Pull over where it is safe to let traffic pass instead of making a line of cars build up behind you. Keep the cab clean, mirrors adjusted and the phone out of your hand. Hired drivers should know the route and the rules before they are alone with the rig.
Records and Insurance
Keep a simple transport log: date, equipment, driver, route and anything found during the walk-around. If a defect turns up, write down what was fixed and who fixed it. When you hire a custom operator or hauler to move equipment, ask for a certificate of insurance and confirm in writing who is responsible for permits, escorts and damage. Ask your insurance agent how your farm policy treats public road use, hired drivers and non-owned equipment, since coverage differs by policy and state. Employee driver rules, including licensing and hours, may also apply; confirm with your state labor department and transportation agency. Look up your state in the directory for hauling and equipment moving providers.
Find providers near you
Pick your state to see vets, custom operators, dealers, elevators and other farm services.
