Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › Greenhouse Equipment Checklist

Greenhouse Equipment Checklist

Greenhouse failures usually happen in the middle of the night or on the hottest afternoon. This checklist covers the heating, cooling, water and backup systems to check first.

Worksheets, Checklists & Calibration Guides3 min read667 words

In short

  • Test heaters, fans and alarms before the season, not during a storm.
  • Size fans and generators with a professional, using your house volume and loads.
  • Check injectors, filters and water quality as part of the equipment list.

Heating and fuel

Test every heater before the cold season, not on the first cold night. Look at burners, heat exchangers and flues for soot, cracks and blockage. Make sure the heater has fresh air supply and venting as the manual calls for, because a poorly vented unit can put carbon monoxide or ethylene into the house, which also hurts plants. Check the thermostats against a reliable thermometer. Test fuel supply and lines for leaks, and know how much propane or fuel you hold. A fuel supplier can tell you what delivery lead times are in a cold snap, so ask before you need them.

Ventilation and cooling

Fans, louvers, shutters and vents have to open and close freely. Clean fan blades and guards, check belts and motors, and test the louver motors, because dirt can cut airflow a good deal. Many greenhouse guides use an air exchange target of about one house volume per minute for summer cooling, so a house holding twenty thousand cubic feet would want fans that move about twenty thousand cubic feet per minute. Your Extension greenhouse specialist or fan manufacturer can tell you what fits your crop and climate. If you use evaporative pads, check the water pump and keep the pads clean.

Controls, sensors and alarms

Test the thermostat or controller, and replace aging sensors. A sensor sitting in direct sun reads too high, and one in a dead corner misses the real conditions, so place it in an aspirated housing if the controller allows. Set a high and low temperature alarm that calls or texts a person who will respond. Test it by raising or lowering the setpoint on purpose. Keep a second thermometer that records the minimum and maximum, so you can see what happened while you were away.

Water and irrigation

Run the whole irrigation system and look at every emitter, nozzle and hose for clogs and leaks. Check filters, injectors and backflow devices. If you add fertilizer through the lines, calibrate the injector by catching a sample and testing electrical conductivity, following the injector and fertilizer label. Test your water source for pH and alkalinity, because they affect nutrients. Check the drain and standing water, because wet floors invite disease and slips.

Power and backup

Many houses lose everything when the power fails. A standby generator and a transfer switch, installed by a licensed electrician, keep fans and heaters running. Exercise the generator on a schedule, change the oil and check fuel. List the loads it must carry, and size it with a professional, because starting loads on motors are higher than running loads. Ask your insurance agent how your policy treats equipment failure and crop loss, since terms vary.

Structure and safety

Inspect the covering for tears, the frame for rust and loose hardware, and the doors and seals. Clear snow and heavy debris from the roof when it builds up. Keep a fire extinguisher at the door, label chemicals, and keep a first aid kit and the contact information for the sprayer you trust. Pesticide and labor rules for greenhouses vary by state, so check with your state department of agriculture.

Seasonal schedule and records

Divide the list into seasons. Before fall, test heaters, fuel lines, thermostats, the generator and the alarm dialer. Before spring, clean fans, pads and louvers and calibrate the injector. Through summer, check the cooling system weekly and look at filters and emitters. After each season, write down what failed and what nearly did. Keep manuals, parts numbers and the supplier phone numbers in one binder in the office. A simple weekly sheet with temperature readings, equipment checks and repairs gives you evidence of patterns, such as a motor that is running hotter each month, before it fails.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading