Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › Manure Application Equipment Checklist

Manure Application Equipment Checklist

Check, calibrate and record your manure spreader or tanker before spreading so the rate you apply matches the plan, the nutrient test and the rules for your state.

Worksheets, Checklists & Calibration Guides3 min read682 words

In short

  • Set the target rate from a manure test, a soil test and your state rules first.
  • Calibrate by load weight or tank volume against measured acres, and repeat when manure changes.
  • Keep leaks fixed, setbacks respected and a written record of every field.

Start with the plan, not the machine

Before touching the spreader, know the rate you intend to apply and why. That rate comes from a manure nutrient test, a soil test, the crop and your state's nutrient management rules, which vary and may restrict timing, setbacks from water and frozen or snow-covered ground. Your Extension office, conservation district or a certified crop advisor can help set a rate. Some states require a nutrient management plan or applicator certification for larger operations, so check with your state department of agriculture or environmental agency. Write the target rate in the units your machine uses, such as tons per acre or gallons per acre.

Inspect the machine

Walk around the spreader or tanker with the manual in hand. Check the box or tank for cracks and leaks, and the floor chain, beaters, augers or paddles for wear. Check gearboxes and grease points, hydraulic hoses for chafing, and the PTO shaft guards, which must be in place. Look at tires, hitch and brakes as you would on any heavy trailer. For liquid systems, inspect valves, pumps, hoses, couplers and the injector or splash plate. Test the machine empty first and listen for noise. Repair leaks before spreading, since a drip across a field and a ditch can become a regulatory problem.

Calibrate a solid spreader

A simple method uses load weight and area. Weigh a loaded spreader on a truck scale, then weigh it empty and subtract to find the load weight. Suppose the load is 8 tons. Spread that load over a measured area. If your target is 10 tons per acre, one load should cover 0.8 acre, since 8 divided by 10 is 0.8. An acre is 43,560 square feet, so 0.8 acre is 34,848 square feet. With a 30 foot spreading width, that is a strip about 1,162 feet long. Mark it with flags, run the load, and adjust ground speed, gate opening or conveyor setting until it matches. Repeat, since manure moisture changes.

Calibrate a liquid tanker

For tankers, find the tank volume from the manufacturer plate, and confirm by filling with a metered source if you can. Suppose the tank holds 3,000 gallons and the target is 4,000 gallons per acre. One load covers 3,000 divided by 4,000, or 0.75 acre. A 20-acre field needs 80,000 gallons, which is about 26.7 loads, so plan for 27. Check the math by multiplying 27 loads by 3,000 gallons to get 81,000. Then measure the actual area emptied per load and adjust speed or flow. Follow the manual for pump settings and track whether the manure is thick or watery on the day.

Placement and safety

Use the setup that fits your fields. Injection or incorporation can reduce odor and runoff compared with surface broadcast, but it needs the right toolbar and soil conditions. Keep spreading away from wells, streams, tile inlets and sinkholes by the distances your state requires, and avoid saturated, frozen or steeply sloping ground. Watch the wind and neighbors. Manure pits and tanks can produce deadly gases, so never enter or lean over one without proper training and equipment. Keep guards on all shafts and keep bystanders clear.

Record keeping

After each job, write down the field, date, acres, manure source, test values, rate applied, weather and soil conditions, and who ran the equipment. Keep calibration notes with the machine. Many states require records for a number of years for permitted operations, so ask what applies to you. Records also help your agronomist adjust fertilizer and show good practice to neighbors or inspectors. Recalibrate when you change manure type, repair the machine, change speed or see uneven spreading. A custom applicator should be able to show you its calibration, so ask before you hire, and look up your state in the directory.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading