Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › Planter Seed Metering Calibration Log

Planter Seed Metering Calibration Log

A planter log records how well each row meters seed, so you can spot worn parts and wrong settings before the whole field comes up uneven.

Worksheets, Checklists & Calibration Guides3 min read645 words

In short

  • Convert spacing and row width to seeds per acre and verify with a one-thousandth acre count.
  • Test every row for skips and doubles and replace worn discs, brushes and tubes.
  • Log speed, settings and conditions so you learn your planter's limits.

What you are logging

A planter drops seed at a target spacing, and every row has to do it separately. The log records what each row actually did compared to what you wanted. Each entry notes the date, field, crop, hybrid or variety, seed lot, planting speed, the meter settings, and the result. Add a column for the person who checked it. Over several seasons you learn what a normal row looks like for your planter, and you will see which rows drift. Your planter manual gives the correct settings for each seed size, vacuum or air pressure, and singulator. Start there and write down what you changed.

The seeding rate arithmetic

Seeds per acre equal 43,560 divided by row spacing in feet times seed spacing in feet. For corn in 30 inch rows, the spacing is 2.5 feet. If the seeds land 7 inches apart, that is 0.583 foot. Multiply 2.5 by 0.583 and you get 1.458. Divide 43,560 by 1.458 and you get about 29,900 seeds per acre. A handy shortcut is to count seeds in one one-thousandth of an acre. In 30 inch rows that length is about 17.4 feet, since 43.56 square feet divided by 2.5 feet is 17.4. Count 30 seeds in 17.4 feet and your population is about 30,000.

The bench and field check

Before planting, lift the planter or use a test stand if your dealer has one. Check each meter for seed skips, doubles and spacing. In the field, plant a short pass at normal speed, then dig up or uncover the seed and measure the spacing for a dozen seeds in each of several rows. Write down the measurements. A good row has most seeds near the target, with few skips and doubles. Compare rows to find the one that is off. Check the monitor against your counts. Monitors are a guide and can be wrong, particularly after a sensor gets dirty.

Common culprits

When one row misbehaves, check the obvious parts first. Worn or warped seed discs, a worn brush or double-eliminator, a cracked vacuum hose, a loose drive chain, a seed tube with a gouge, and a down-pressure setting that bounces the unit are all common. Seed size matters too, since flat and round kernels may need different discs or settings. Seed treatments and talc or graphite can change how seed flows. Keep a short list of parts you replaced and the date.

Speed and conditions

Seeding accuracy usually falls as ground speed rises, and the point where it falls off differs for each planter and meter. Record the speed for each test and note the field conditions, such as residue, soil moisture and roughness. Over a season you will have your own speed limit for good spacing. Check the manufacturer's guidance and your dealer's setup recommendations, and keep your records for comparison.

Mistakes to avoid

Do not set the planter once in March and forget it, do not plant at the speed the monitor allows rather than the speed the seed allows, and do not skip the check after changing seed lots.

Using the log over time

After planting, walk the field at emergence and count plants in the same 1/1000 acre lengths you checked at planting. The difference between seeds dropped and plants up tells you something about seedbed, depth and seed quality, not just the meter. Write both numbers in the log. After a few seasons you will see whether a row that looks fine on the bench still comes up poorly, and whether a field type or tillage system changes your emergence. Share the results with your seed dealer.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading