Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › Manure Spreader Calibration Worksheet

Manure Spreader Calibration Worksheet

A spreader that is never checked puts on whatever it puts on. Here is how to measure your real application rate and set it where your nutrient plan says it should be.

Worksheets, Checklists & Calibration Guides3 min read713 words

In short

  • Measure the real rate by weighing loads or catching manure on tarps, then divide by area.
  • Recalibrate when the manure, bedding, speed or equipment changes.
  • Pair every rate with a lab analysis and follow your state rules and nutrient plan.

Why the dial setting is only a guess

Spreader charts and gate settings are written for average material. Your manure is not average. Bedded pack, scraped lot manure, poultry litter and compost all differ in moisture, density and how they feed out of the box. A setting that gave 10 tons per acre last spring can give 7 or 14 this spring after the herd changed rations or the bedding changed. Calibrating takes an hour or two, and it is the only way to know whether your nutrient management plan is being followed in the field. Do it for each spreader and each type of manure, and repeat whenever the material changes noticeably. Check the operator manual for the correct PTO speed and apron settings before you start.

The load weight method

This one needs a scale, a truck scale or a set of portable axle pads. Weigh the spreader loaded, spread the whole load, then weigh it empty. The difference is the weight of manure. Say the loaded weight is 14,000 pounds and empty is 8,000. That is 6,000 pounds, or 3 tons. Now measure the area covered. Count the passes, measure the effective spread width, and pace or measure the length. With a 30 foot effective width over 1,000 feet, the area is 30,000 square feet. Divide by 43,560 square feet per acre and you get about 0.69 acre. Three tons over 0.69 acre is roughly 4.4 tons per acre. To raise the rate, slow the apron or drive slower. To lower it, do the opposite.

The tarp method for checking in the field

When there is no scale handy, lay out tarps or shallow pans of known size across the spread width, then drive over them at normal speed. A 3 foot by 3 foot tarp is 9 square feet. Collect and weigh the manure on it. If you catch 4 pounds, that is 0.444 pounds per square foot. Multiply by 43,560 and you get about 19,360 pounds per acre, or 9.7 tons. Use at least five tarps spaced across the width, because the pattern at the edges is usually lighter than under the beater. Averaging the tarps gives your rate. The spread of the numbers tells you about your pattern. If the middle runs double the edges, fix that before you worry about the average.

Liquid manure tankers

For tankers the math is simpler. Gallons per acre equals total gallons applied divided by acres covered. A 3,000 gallon tanker emptied over 2 acres is 1,500 gallons per acre. Know the true capacity of the tank, because the number stenciled on the side is often optimistic. Meter flow if you have a flow meter. If not, calibrate by pumping a known volume out of a measured storage cell. Watch for pump wear, since a tired pump moves less at the same tractor speed. Injection and drag hose setups have their own calibration steps in the manufacturer manual.

What to record and what to confirm

Write down the date, spreader, manure type, gate or apron setting, PTO speed, ground speed, effective width, and the measured rate. Pull a manure sample for a lab test at the same time, since the rate only means something when paired with nutrient content. Application rules, setbacks, winter spreading limits and plan requirements vary by state and sometimes by county. Confirm yours with your state department of agriculture, the Natural Resources Conservation Service office or your county Extension educator. If a custom hauler spreads for you, ask for the rate they measured and the date of their last calibration, and get it in writing.

Mistakes to avoid

The usual ones are calibrating with a half-empty box, measuring at a speed you never actually drive, and trusting one tarp. Another is forgetting that frozen or wet manure flows differently than dry. And a rate measured in tons as spread is not the same as a rate of nitrogen, so do not mix the two. Keep the calibration sheet in the cab where the next driver will see it.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading