Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › ATV Sprayer Calibration Worksheet

ATV Sprayer Calibration Worksheet

A small ATV sprayer is easy to get wrong because everything is small. Here is the worksheet method, with the math, for applying the right gallons per acre.

Worksheets, Checklists & Calibration Guides3 min read664 words

In short

  • Time a measured course to get your real ground speed, twice, and average it.
  • Gallons per acre equals nozzle flow times 5,940 divided by speed times spacing.
  • Calibrate with water, then write each result on the worksheet.

What you are calibrating

You are working out one thing: how many gallons the sprayer puts on an acre. That comes from three numbers, the flow from each nozzle, your ground speed, and the spacing between nozzles. If any one is off, the rate is off, and so is the herbicide dose in each gallon. Always follow the product label for the rate and the equipment manual for pressure and nozzle choices. Never calibrate with the actual chemical. Use clean water.

Measure your speed

Speed is the number most people guess. Measure out a course, say 200 feet, on ground like what you will spray, such as sod or a pasture. Run it with a full tank, since a heavy ATV may slip differently. Time the pass in seconds. If it takes 45 seconds, your speed in feet per second is 200 divided by 45, or 4.44. Divide by 1.4667 to convert to miles per hour, which gives about 3.0. Do it twice, in both directions, and average. Mark the throttle or gear so you can repeat it.

Measure the flow

Run the sprayer with water at the working pressure. Catch the output from one nozzle for one minute in a measuring jug marked in ounces. Do this for several nozzles. If they differ by more than a few percent from the average, clean or replace the outliers. Say the average catch is 25.6 ounces per minute. There are 128 ounces in a gallon, so that is 0.2 gallons per minute. Also check the pressure gauge, because a gauge that is off changes everything.

Do the arithmetic

The gallons per acre formula is flow per nozzle in gallons per minute times 5,940, divided by speed in miles per hour times nozzle spacing in inches. With 0.2 gallons per minute, 3.0 miles per hour and 20 inch spacing, that is 0.2 times 5,940, which is 1,188, divided by 60, giving 19.8 gallons per acre. If you wanted 20, you are close enough. If you wanted 15, you need a smaller nozzle or a faster pass, not a guess.

Mix the tank

Divide the tank size by the gallons per acre to find acres per tank. A 15 gallon tank at 19.8 gallons per acre covers about 0.76 acre. If the label calls for 2 pints of product per acre, that tank gets about 1.5 pints. Round carefully and write the figure on the tank in paint pen. Mix a bit of a small test batch before a full tank if the label mentions compatibility. Check the label for rates, buffers, restricted areas and protective gear.

Record and recheck

On your worksheet write the date, nozzle type, pressure, speed, flow, spacing and result. Recheck at the start of each season, after any nozzle swap, and when the ground changes. A dry hayfield and a wet pasture will not give the same wheel slip. Many state pesticide programs have rules about records for restricted use products, so ask your state agriculture department what yours requires. Your county Extension office may have calibration help.

Common mistakes to avoid

The usual errors are guessing speed, trusting a worn nozzle, and calibrating on a different surface than the one you spray. Another is mixing up ounces and gallons, since 128 ounces make one gallon, and a slip there throws off everything. People also forget that tip wear raises flow over time, so a nozzle that read right two seasons ago may not now. Check the nozzle chart for your tip at your pressure, and compare it to what you catch. If catch and chart disagree by a lot, replace the tip rather than chase the problem with the throttle. A cheap nozzle is cheaper than a burned pasture.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading