Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Worksheets, Checklists & Calibration Guides › Forage Harvester Setup Checklist

Forage Harvester Setup Checklist

A forage harvester that is set up well chops cleaner, feeds better and burns less fuel. Use this checklist before the first load, and again when the crop changes.

Worksheets, Checklists & Calibration Guides3 min read742 words

In short

  • Sharp knives and a set shear bar gap save fuel and give a cleaner cut.
  • Check length of cut and kernel damage on a real sample, not only by the dial.
  • Put cut length, processing and breakdown plans in writing with any custom chopper.

Start with the manual and the shop

Pull out the operator manual before you touch a wrench, because intervals, torque values and settings differ between machines. Walk the harvester with the power off and the key out. Check the feed rolls, the cutterhead, the shear bar, the kernel processor, the spout and the blower for wear, loose bolts and cracks. Grease every fitting that calls for it, and check gearbox and hydraulic oil levels. Look at the drive belts and chains for stretch and damage. Replace what is worn now, in the shop, rather than at midnight in a corn field with a truck waiting.

Knives and shear bar

Sharp knives are the single biggest factor in cut quality and horsepower use. A dull knife tears the crop and leaves long stringy pieces, and it pulls more fuel. Sharpen or replace knives according to the manual, and keep the set balanced so the cutterhead does not vibrate. Then set the clearance between the knives and the shear bar. The usual method is to rotate the cutterhead by hand and slide a thin shim or feeler gauge in the gap, adjusting until the manual spec is met. Too tight and metal touches metal. Too loose and the crop is smashed rather than sheared.

Length of cut

Theoretical length of cut depends on knife count, feed roll speed and the gear or setting you choose, and the manual gives a table. For corn silage, many Extension guides suggest a length in the range of about three eighths to three quarters of an inch, but ask your nutritionist what fits your herd or feeding program. Haylage and grass need other settings. If cattle have to be fed long effective fiber, a longer cut may help, and a very short cut can pack but hurt rumen health. Check the actual chop by taking a sample from the wagon, not just the dial.

Kernel processor

Corn silage needs the kernels cracked so animals can use the starch. Set the processor roll gap according to the manual, then test results. A common field check is to grab about a quart of fresh chopped silage, spread it out, and look at how many kernels are whole or only chipped. Your nutritionist or Extension office may offer a scoring method, which is more objective than looking. Make adjustments for crop maturity, because drier, harder kernels need a tighter gap, and a very wet crop may not.

Crop moisture and field setup

Moisture decides how the silage packs and ferments. Whole plant moisture targets depend on the storage type, such as bunker, bag or upright, so check an Extension silage guide before you start. Take a sample from several places, since a field can vary. Set the header height based on your stalk cutting goal, the spout aim based on wagon or truck, and the ground speed so the machine is not choking or running half loaded. Watch for rocks, because stones and metal wreck cutterheads. Many harvesters carry a metal detector, so test it as the manual directs.

Hiring a custom chopper

If you hire a custom crew, ask who sets the cut and who is responsible for the processor check. Get these in writing: length of cut, kernel processing target, the rate, how trucks or wagons are staffed, and what happens when it rains. Ask how often they replace knives and how they cover breakdowns. Your Extension custom-rate survey can show how others price the work, but rates vary by region.

Mistakes that cost tons

A few errors show up every season. Running knives past their life is the first. The second is setting the processor gap once and never checking it again as corn dries down during the harvest window. The third is a spout or trucks that are poorly matched to the machine, so the harvester sits idle waiting on haulers. Pack is the fourth. Even a perfect chop fails if the pile is not packed tight and covered fast, so plan tractors, weight and plastic before harvest starts. Keep a short log of knife changes, processor settings and field moisture, so next year you start from a better place than a guess.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading