Farm service guides and a state-by-state directory for farmers and ranchersA farm.FM network site · Farm news →
AgServicesDirectoryWho to call, state by state
Home › Guides › Aerial, Drone & Precision Services › Soil Electrical Conductivity Mapping

Soil Electrical Conductivity Mapping

Soil electrical conductivity maps show how texture, moisture and salts vary across a field, and they work best when you pair them with a few well-placed soil samples.

Aerial, Drone & Precision Services3 min read708 words

In short

  • Ask what the sensor reads, how it was checked, and what the pass spacing is.
  • Scan when soil moisture is steady, and pair every map with a few lab-tested samples.
  • Get the raw points and zone files in writing, and use only zones you can manage differently.

What the map actually measures

A conductivity sensor pushes a small current through the soil and reads how easily it flows. That number is called apparent electrical conductivity, or ECa, and it is a blend of several things at once: clay content, soil moisture, organic matter, salts and compaction. Clay and wet soil conduct well. Dry sand conducts poorly. So the map is not a fertility map. It is a map of where the soil changes, which is useful because those changes often line up with yield differences you already see from the combine seat. Units are usually millisiemens per meter or decisiemens per meter, and one decisiemens per meter equals 100 millisiemens per meter. Check which unit your provider uses before you compare two maps.

Contact sensors versus non-contact sensors

Contact sensors use coulters that cut into the ground and are pulled behind a truck or ATV. They often log a shallow and a deep reading at the same time. Non-contact sensors use electromagnetic induction and are carried or dragged over the surface without cutting in. Contact units read closer to the surface and can struggle in very dry, hard or rocky ground where the coulters lose contact. Induction units handle those conditions better but can be thrown off by nearby metal, fences and buried lines. Ask the provider which type they run, what depths it reads, and how the sensor was checked against a reference before your job. Follow the manufacturer manual on speed and warm-up time.

Timing and field conditions

Soil moisture swings the readings, so a map taken right after a rain will not match one taken in a dry spell. Ask for moisture to be reasonably even across the field, and avoid frozen ground, standing water and freshly worked soil. Many growers scan once in a stable season and reuse the zones for years, since texture does not change quickly. Salt problems are the exception and may need a repeat scan. Residue and heavy trash can also foul contact coulters, so a field cut and cleared is easier to scan. Settle the timing in writing before the crew arrives, and agree on who reschedules if the weather turns.

Pass spacing and coverage

Ask for the pass spacing, because it drives both the cost and the detail. As a simple example, an 80 acre field that is 2,640 feet wide, scanned at 60 foot spacing, takes 44 passes across it. Tighten the spacing to 30 feet and you double the passes, and you get a sharper picture of narrow soil features like old stream channels. Wider spacing is cheaper and often fine for broad zones. Also ask whether the provider drives headlands and field edges, since the logs from turns are usually thrown out.

Ground-truthing with soil samples

A conductivity map without samples is a guess in color. Good providers pick sample points that cover the range of values, not just the middle, and then send those samples for texture and organic matter tests. Those results tell you what each color means in your field. A high reading could be clay, or it could be salt, and the lab work separates them. Ask who picks the sample points, how deep they sample, what the lab will report, and whether the sample locations come back to you with GPS coordinates.

Turning the map into zones

The raw map is a set of points. Someone has to clean out bad readings and smooth the data into a handful of zones, usually three to five. More zones are not better. If you cannot manage a zone differently, it is just a prettier map. Use the zones for variable seeding rates, soil sampling by zone, drainage planning and test strips. Ask for the files in a format your equipment and software can read, and ask who owns the raw data. Your state Extension office or a certified crop adviser can help you read the zones against your own yield history.

Find providers near you

Pick your state to see vets, custom operators, dealers, elevators and other farm services.

Keep reading